AcuRite 00607 Dokumentacja Strona 52
- Strona / 224
- Spis treści
- BOOKMARKI
Oceniono. / 5. Na podstawie oceny klientów
Southwestern Industries, Inc.
ProtoTRAK
SMX K2, K3, K4 & Retrofit Safety, Installation, Maintenance, Service & Parts List Manual
48
Do the following service codes and procedures:
• Code 33
Software Identification. This is needed if you call SWI Customer Service.
• Code 313 Configuration Values
• Code 123 Calibration Mode.
Possible Cause Check This
Configuration file corrupt Load default configuration by going to code 313
Not saving Calibration values Replace Computer/Pendant module.
See Computer/Pendant
If calibration factors are being saved, but the measurements are not repeating or are not accurate:
• See Measurements Are Not Repeating
• See Measurements Are Not Accurate
3.3.10 Auxiliary Functions Not Working (Option on 3 Axis
Machines Only)
The Auxiliary Functions will not turn on or off at the programmed times. There are 3
Auxiliary Functions:
1. Activates or deactivates a "110VAC Receptacle" typically used for a coolant pump or
solenoid for mister.
2. Sends an electrical signal to rotate the turret on a "Haas Indexer".
3. Turns the "Spindle Off" at the end of a programmed event. (Note: This function is
not available for retrofits.).
In order to run the above auxiliary functions in run mode, the accessory key on the front
of the pendant must be in the AUTO mode. Press and hold to activate AUTO mode.
All of the auxiliary function signals are carried down to the cable breakout box through
umbilical #2. Each function then has its own relay inside this box. If one of these relays
fail then these features will not work.
Do the following service code and procedures:
• Code 33 Software Identification. This is needed if you call SWI Customer Service.
Possible Cause Check This
Bad 110VAC "Coolant or solenoid"
receptacle fuse
Check if the fuse light indicator next to the plug is lit.
Verify that the fuses are good or bad by checking the
resistance of the fuses using an Ohmmeter.
Poor cable connections
Check all the cable connections on the cable
breakout box, Coolant Pump, and Air Solenoid
(Located on the Air Regulator). In particular, check
umbilical # 2 cable, which carries the auxiliary
function signals.
Faulty "Indexer" connector
Check for continuity between pins 3 and 4, when the
output of the Haas Indexer connector is activated.
Bad cable breakout box
Check 110 V power coming out of the AC E-stop port
with the E-stop in the out position. This will cause
the spindle to not run.
- ProtoTRAK 1
- K2, K3, K4 & 1
- Retrofit 1
- Fax 310.764.2668 2
- Fax 310.886.8029 2
- Table of Contents 3
- 1.0 Safety 6
- 1.3 Safety Precautions 8
- 2.0 Installation 11
- 2.2 Uncrating 13
- 2.5 Machine Specifications 15
- 2.9 Cleaning 21
- Placement of Levels 22
- 2.11 Electrical Connection 23
- Not for retrofit 24
- Figure 8 24
- Figure 9 25
- Figure 9-1 26
- Figure 11 29
- Transformer Option Schematic 29
- 2.14 Cable Interconnections 31
- Figure 14 33
- Pendant - Right Side 33
- P/N: 24000-1 33
- Figure 15 34
- Cable Connection Diagram 34
- Non-Spindle Control 34
- Figure 16 36
- 2.15 Lubrication 37
- 2.15.2 Head Lubrication 39
- • X = 1.318 40
- • Y = 1.318 40
- Figure 18 41
- Euclid Block 41
- 3.1.1 Poor Finish 42
- 3.1.2 Circles Out of Round 43
- 3.2.1 Run Away Axis 45
- 3.2.2 Slow Down Axis 46
- 3.2.3 Axis Will Not Jog 46
- 3.2.5 Vibration in Motion 47
- 3.2.6 Searching Axis 48
- 3.3.1 Display Blanks 49
- 3.3.3 Keyboard Lockup 49
- 3.3.4 Fault X or Y 49
- 3.3.8 System Shuts Off 51
- Machines Only) 52
- Direction 56
- 3.5.4 Head Noise 59
- 4.0 Diagnostics 61
- 4.1.3 Lubrication 62
- 4.1.4 Machining Set-Up 62
- 4.1.4.1 Spindle Speeds 63
- 4.1.4.2 Feedrates 63
- 4.4 Motor Diagnostics 66
- 4.5 Servo Driver 67
- 4.6 Glass Scales 68
- 4.7 TRAK Sensors 69
- 4.8 Electrical 71
- 4.8.4 Cable Connections 72
- Figure 19 73
- Electrical Box Schematic 73
- Figure 20 75
- Figure 21 76
- LEDs on Spindle 76
- Control Board 76
- 4.9 Service Codes 77
- 4.9.1 Software Codes 77
- 4.9.2 Machine Set-up Codes 78
- 4.9.3 Diagnostic Codes 81
- & Maintenance 84
- Figure 22 85
- Figure 23 86
- Figure 24 88
- Flash Disk Replacement 88
- Flash Disk Parts List 88
- Flask Disk Replacement 88
- 5.1.6 TRAK Sensor 89
- Figure 25 90
- M5 Base Mounting 90
- Figure 26 91
- TRAK Sensor Mounting 91
- Figure 27 92
- K Mill Sensor Assembly 92
- Z-Axis Glass Scale Assembly 95
- Figure 29 96
- Glass Scale Alignment 96
- 5.1.8 Power Drawbar 97
- Figure 30 98
- Power Drawbar Assembly 98
- Figure 31 100
- X-Axis Drive Assembly 100
- Figure 33 105
- Spindle Motor Wiring 105
- Figure 36 107
- Figure 37 109
- Figure 38 110
- 5.2 Maintenance 111
- Figure 39 111
- Table Gib Adjustment 111
- Figure 40 112
- Table Gib Screw 112
- Figure 42 114
- Figure 43 115
- Calibration Set-Up 115
- 5.2.3.2 Tramming the Head 117
- Side-to-Side Alignment 117
- Back to Front Adjustment 118
- 5.2.4 Limit Switch Option 119
- 6.0 Retrofit Installation 121
- 7.0 Installation Procedures 123
- X-Axis Ball Screw 125
- Figure 51 127
- Figure 55 133
- Figure 56 136
- X Motor Mounting 136
- Figure 58 141
- Z-Axis Glass Scale Assembly 141
- Figure 59 142
- X Bracket Installation 142
- Figure 60 143
- Y Bracket Installation 143
- Figure 61 144
- 148
- 7.9 System Interconnection 150
- Figure 66 151
- Figure 68 156
- & Covers Assembly 156
- Figure 68-1 158
- Ball Screw Module 158
- P/N 24250 158
- Parts List Ball Screw Module 159
- 8.4 Lagun Z Axis Cutout 160
- Figure 69 160
- 9.2 Warranty 161
- 9.3 Replacements 163
- Figure 100 164
- Figure 104 169
- Pulley Pinion Sub-Assembly 169
- P/N: 20697-4 169
- Figure 105 170
- Lower Vari-Disc Sub-Assembly 170
- P/N: 20697-5 170
- Figure 106 172
- Upper Vari-Disc Sub-Assembly 172
- P/N: 20697-6 172
- Figure 109 176
- Bottom Housing Assembly 176
- Figure 110 180
- P/N: 20698-1 180
- Parts List 192
- Head Top Assembly - 24692 192
- Figure 120 194
- Hi-Low Shift Clutch 194
- Sub-Assembly 194
- P/N: 20778-2 194
- Figure 121 196
- Hi-Low Shift 196
- P/N: 20778-3 196
- Figure 125 202
- Speed Change Handwheel 202
- P/N: 20778-7 202
- Figure 127 204
- Lower Head Assembly 204
- Figure 128 208
- Worm Gear Cradle 208
- P/N: 20779-1 208
- Figure 134 214
- K2/K3 Base Machine P/N 20785 214
- Figure 135 218
- K4 Base Machine P/N 26900 218
- Parts List - K4 Base Machine 219
- Figure 136 221
- P/N: 23470-220 or 23470-440 221
- Figure 137 222
- P/N 23470-220 or 23470-440 222
- TRAK Warranty Policy 224
Powiązane produkty i podręczniki dla Stacje pogodowe AcuRite 00607
Stacje pogodowe AcuRite 00838 Instrukcja Obsługi
(12 strony)
(12 strony)
Stacje pogodowe AcuRite 00622 Instrukcja Obsługi
(20 strony)
(20 strony)
Stacje pogodowe AcuRite 75075 Instrukcja Obsługi
(12 strony)
(12 strony)
Stacje pogodowe AcuRite 8553W Instrukcja Obsługi
(16 strony)
(16 strony)
Stacje pogodowe AcuRite 01055 Instrukcja Obsługi
(12 strony)
(12 strony)
Stacje pogodowe AcuRite 02007 Instrukcja Obsługi
(20 strony)
(20 strony)
Stacje pogodowe AcuRite 02026 Instrukcja Obsługi
(16 strony)
(16 strony)
Stacje pogodowe AcuRite 02001 Instrukcja Obsługi
(12 strony)
(12 strony)
Stacje pogodowe AcuRite 00827 Instrukcja Obsługi
(12 strony)
(12 strony)
Stacje pogodowe AcuRite 00606 Instrukcja Obsługi
(12 strony)
(12 strony)
Stacje pogodowe AcuRite 02038 Instrukcja Obsługi
(16 strony)
(16 strony)
Stacje pogodowe AcuRite 02028 Instrukcja Obsługi
(12 strony)
(12 strony)
Stacje pogodowe AcuRite 614 Instrukcja Użytkownika
(457 strony)
(457 strony)
Stacje pogodowe AcuRite 00754 Instrukcja Obsługi
(12 strony)
(12 strony)
Electrolux IK275010RE Handbücher
Bedienungsanleitungen und Benutzerhandbücher für Gefrierschränke Electrolux IK275010RE.
Wir stellen 2 PDF-Handbücher Electrolux IK275010RE zum kostenlosen herunterladen nach Dokumenttypen zur Verfügung Bedienungsanleitung
Electrolux IK275010RE Bedienungsanleitung (48 Seiten)
Marke: Electrolux | Kategorie: Freezers | Größe: 1.48 MB |
Inhaltsverzeichnis
Electrolux IK275010RE Bedienungsanleitung (48 Seiten)
Marke: Electrolux | Kategorie: Freezers | Größe: 1.48 MB |
Inhaltsverzeichnis
Weitere Produkte und Handbücher für Gefrierschränke Electrolux
| Modelle | Dokumententyp |
|---|---|
| ER8199B | Bedienungsanleitung Electrolux ER8199B Brugermanual [en] , 17 Seiten |
| EC5109N |
Bedienungsanleitung
Electrolux EC5109N User Manual,
16 Seiten
|
| ER9010B | Bedienungsanleitung Electrolux ER8109B Användarmanual, 16 Seiten |
| EN3451JOW |
Bedienungsanleitung
Electrolux EN3451JOW User Manual [en] ,
20 Seiten
|
| EC3200AOW2 |
Bedienungsanleitung
Electrolux EC3200AOW2 Brugermanual,
72 Seiten
|
| EN3201JOW | Bedienungsanleitung Electrolux EN3201JOW Brugermanual [de] [en] [fr] [nl] , 20 Seiten |
| ECP21110W |
Grundlegende Anleitung
Electrolux ECP21110W Basic Guide,
16 Seiten
|
| ERF4161AOW |
Bedienungsanleitung
 
Electrolux ERF4161AOW Používateľská príručka,
40 Seiten
|
| ERN34800 |
Bedienungsanleitung
Electrolux ERN34800 Brugermanual,
44 Seiten
|
| RNN2800AOR |
Bedienungsanleitung
Electrolux RNN2800AOR User Manual [de] [en] [es] [fr] ,
76 Seiten
|
| EU7120C |
Bedienungsanleitung
Electrolux EU7120C Brugermanual,
12 Seiten
|
| EUF2325 |
Bedienungsanleitung
Electrolux EUF2325 User Manual [da] [et] [sv] ,
11 Seiten
|
| EUG1105AOW |
Bedienungsanleitung
Electrolux EUG1105AOW Manuel utilisateur [en] ,
48 Seiten
|
| ER8397B | Bedienungsanleitung Electrolux ER8397B Brugermanual, 16 Seiten |
| ERN2001FOW |
Bedienungsanleitung
Electrolux ERN2001FOW User Manual,
64 Seiten
|
| EUF2744AOW |
Bedienungsanleitung
Electrolux EUF2744AOX Uživatelský manuál [de] [en] ,
48 Seiten
|
| ENB43691S |
Bedienungsanleitung
Electrolux ENB43691S Handleiding,
96 Seiten
|
| ENN2854COW | Bedienungsanleitung Electrolux ENN2854COW Brugermanual [de] [en] [es] [fr] , 68 Seiten |
| EN3453MOW | Bedienungsanleitung Electrolux EN3453MOW Brugermanual [et] , 20 Seiten |
| ECO26112W | Bedienungsanleitung Electrolux ECO26112W Användarmanual, 16 Seiten |
© 2020, manymanuals.pl. Wszelkie prawa zastrzeżone. | 0.028 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Komentarze do niniejszej Instrukcji